LaserMax Stud Sensor LMS-JMX-H Bedienungsanleitung PDF herunterladen

To avoid unintentional battery drain,

the J-Max is set to turn off after 30

minutes of constant use. While in the

time out mode, simply cycle the

activation switch off to re-cycle the

laser, and turn it back on.







TIME OUT!

LEFT GRIP

RIGHT GRIP

LASER SIDE PLATE

GRIP SCREW

SIDE PLATE SCREWS (2)

BATTERIES (2)

LARGE HEX WRENCH (5/64)

ALIGNMENT TOOL (.035”)

LASER WARNING LABEL

BATTERY COVER

installation guide

LMS-JMX-H; LMS-JMX-NH

1.800.527.3703

installation guide

Installing the J-Max



 Laser System

Ⓑ

Ⓒ

Ⓖ

Ⓗ

Ⓐ

Ⓔ

Ⓕ

Ⓐ

Ⓑ

Ⓒ

Ⓓ

Ⓔ

Ⓕ

Ⓖ

Ⓗ

Ⓘ

Ⓙ

What’s in the Box

To insert or replace batteries: Using a small flat blade screwdriver, loosen the battery

cover screw until the battery cover (J) is able to rotate. Rotate the battery cover (J)

until you are able to remove the batteries. Replace the batteries by inserting the

negative (-) end first. The batteries’ positive (+) printed side must face out. Rotate

the battery cover to its original orientation. Tighten the battery cover screw until

snug—do not over tighten. Confirm that the laser will now activate. If the laser will

not turn on—retighten the screw and try again. (See Figures f-h)

* Remove batteries when not in use for extended periods of time to preserve battery life.

Inserting the Batteries















Make sure your gun is unloaded. Double check to

verify your handgun is safe before proceeding.

Unscrew the mounting hardware on your existing

grips (in most cases this will be a single flat head

screw; refer to gun owners manual for proper size)

and remove grips. Remove the two (2) factory side

plate screws. Do not remove factory side plate or

side plate yoke screw! (See Figures a & b)

Place left side of revolver grip frame over Left Grip

(A), so that the grip frame aligns with features in Left

Grip (A). (See Figure b)

Place Laser Side Plate (C) over right side of grip

frame, aligning it with grooves and screw holes in

frame. (See Figure c)

Insert Side Plate Screws (E) into holes in Laser Side

Plate (C). Tighten with the Large Hex Wrench (G).

Do not over tighten. (See Figure d)

Position Right Grip (B) over Laser Sight Plate (C),

aligning it with grooves & screw hole.

Insert Grip Screw (D) into hole in Right Grip (B) and

through frame. Secure with flat blade screwdriver.

(See Figure e)

DO NOT REMOVE

screw below cylinder

Ⓙ

c d

Affix Laser Warning

Label (I) onto your

firearm as close to

the laser as possible

Ⓘ

Laser Side Plate (C)

Ⓓ

1 2

TIME OUT! 1
LMS-JMX-H; LMS-JMX-NH 2

Inhaltsverzeichnis

Seite 1 - TIME OUT!

To avoid unintentional battery drain, the J-Max is set to turn off after 30 minutes of constant use. While in the time out mode, simply

Seite 2 - LMS-JMX-H; LMS-JMX-NH

The hole at the top adjusts elevation (vertical alignment).* You can easily fine tune your laser to accommodate any weapon platform, type

Kommentare zu diesen Handbüchern

Keine Kommentare

LaserMax Stud Sensor LMS-JMX-H Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Auto-Kits LaserMax Stud Sensor LMS-JMX-H herunter. LaserMax Stud Sensor LMS-JMX-H User's Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern